Home > Arch Linux > Arch Linux No Sound

Arch Linux No Sound

Contents

As this can cause problems with headset, the responsible module can be deactivated. What is the meaning of "cow in the middle"? Each time the system starts up, the card profile is disabled and the pulseaudio daemon cannot select it. Automatically switch to Bluetooth or USB headset Add the following: /etc/pulse/default.pa # automatically switch to newly-connected devices load-module module-switch-on-connect My Bluetooth device is paired but does not play any sound See http://seesbg.com/arch-linux/arch-linux-virtualbox-sound-not-working.html

Reason: The problem is using ALSA tools for controlling PulseAudio, see PulseAudio#Keyboard volume control for better way. (Discuss in Talk:PulseAudio/Troubleshooting#) In setups with multiple outputs (e.g. 'Headphone' and 'Speaker') using plain defaults.pcm.+card 2; defaults.ctl.-card 2; # Same effect on a default setup, however if defaults node was removed or defaults.pcm.-card 2; # type has been changed merge operation mode will result in Note: This is only an example for Asus Xonar Essence STX. Only one vdownmix plug can be used; if you have 7.1 channels, you will need to use surround71 instead the configuration above. https://bbs.archlinux.org/viewtopic.php?id=125092

Arch Linux No Sound

Sound works fine when I run cinnamon or gnome, so I'm assuming it's something I'm not starting via the herbstluftwm autostart, but I don't know what it could be. Also to note: I get the terminal beeps no problem. Earlier kernels did work. Delimiters around Array Does the Rothschild family own most central banks?

Stop Pulse, erase the "stream-volumes" in ~/.config/pulse and/or ~/.pulse and restart Pulse. Dmix is not enabled by default for digital output (S/PDIF) and will require the configuration snippet below. To test anyway, the commands are pulseaudio --kill and pulseaudio --start. Arch Linux Sound Stopped Working when you use this "hw:" type of format, the application is going to take the sound file and send it directly to your sound card.

Applications setting their volume on startup will therefore cause the system volume to "jump". Arch Linux Pulseaudio Note: For reference, ALSA stores its settings in /var/lib/alsa/asound.state ALSA Firmware The alsa-firmware package contains firmware that may be required for certain sound cards (e.g. You should hear static from each channel in turn. How does Berlin Transport Validation Stamp mark current date and/or expiry date?

Muted audio device If one experiences no audio output via any means while using ALSA, attempt to unmute the sound card. Arch Linux No Sound After Update In order to do so you will have to prevent Pulse from restarting after being killed. ~/.config/pulse/client.conf # Disable autospawning the PulseAudio daemon autospawn = no Daemon startup failed Try resetting There are different assignment types and styles available. Ensure sane settings are present, specifically those of muted and volume.

Arch Linux Pulseaudio

Managing ALSAEqual states Install the alsaequal-mgrAUR package. http://unix.stackexchange.com/questions/104270/how-do-i-enable-sound-in-this-fresh-arch-install By default, it will try to use the speexrate converter to do so, and fallback to low-quality linear interpolation if it is not available[3]. Arch Linux No Sound Archlinux does install pulse-audio by default thus it is likely to work as a mixer where as ALSA probably will not. –Claris Jan 29 '15 at 18:52 RThe OP Arch Alsa The number of fragments is simply buffer_size/fragment_size, which in this case (250/125) is 2: /etc/pulse/daemon.conf ; default-fragments = 2 ; default-fragment-size-msec = 125 Restart the PulseAudio daemon (4/4) $ pulseaudio -k

so if you want to use ALSAEqual with mpd or another software running under different user, you can configure it using $ su mpd -c 'alsamixer -D equal' or for example, http://seesbg.com/arch-linux/arch-linux-netctl.html One possible cause of no sound after install is that PulseAudio detects the wrong output device as a default. In darker days this used to be tricky and error prone but nowadays plugins exist to easily take care of this task. Using double quotes here automatically sets values data type to string, so in the above example setting defaults.pcm.!card "2" would result in retaining last default device, in this case card 0. Arch Linux Audio

This site is not affiliated with Linus Torvalds or The Open Group in any way. Then add the following to your ALSA configuration file of choice (either /etc/asound.conf or ~/.asoundrc): pcm.upmix71 { type upmix slave.pcm "surround71" delay 15 channels 8 } You can easily change this What episode of Star Trek is this creature on? Check This Out Configuration The system configuration file is /etc/asound.conf, and the per-user configuration file is ~/.asoundrc.

Thanks. Restart Alsa This means previously run applications are not affected by the newly set fallback device. Offline #16 2011-08-25 03:30:16 helmut Member Registered: 2008-10-10 Posts: 65 Re: [SOLVED] sound not working Thanks for the hint.

Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the

Assignments and Separators Assignments define a value of a given key. But after a reboot, the sound card worked well.You helped me a lot to solve that problem and thanks for the "lesson". How does sender and receiver clock time periods synchronize in data communication? Pulseaudio Daemon Startup Failed No cards If PulseAudio starts, run pacmd list.

Simple assignment # This is a comment. Use the standard shell '--' pseudo argument to disable argument parsing before the negative argument. Cannot update configuration of sound device in pavucontrol pavucontrol is a handy GUI utility for configuring PulseAudio. this contact form Create the actual configuration.

key value0; key valueN; key value0, key valueN, key value0 key valueN key value0 key valueN Compound assignments use braces as separators. Should I report it? First verify that the variables default-fragments and default-fragment-size-msec are not being set to non default values in the file /etc/pulse/daemon.conf. Did you tried to run alsaconf? –Ivan Jan 18 '12 at 21:17 Headphones did not work either.

Teenage daughter refusing to go to school Giving change in smaller denominations so customers can tip? How? When Pulse comes back after a few seconds, applications will not alter the global system volume anymore but have their own volume level again. Though I used alsamixer to ensure no volumes are muted.

If the audio file was recorded in 2 channels, 24 bits, 192000 samples per second and your sound card hardware can't handle that, then ALSA and the application will barf.BUT... All audio now works. Then insert the following options with the corresponding card. Arch Linux HomePackagesForumsWikiBugsAURDownload Index Rules Search Register Login You are not logged in.

more hot questions question feed about us tour help blog chat data legal privacy policy work here advertising info mobile contact us feedback Technology Life / Arts Culture / Recreation Science If you want OSS applications to work with dmix, install the alsa-oss package as well. If the pulseaudio -vvvv command shows error like: E: [pulseaudio] module-udev-detect.c: You apparently ran out of inotify watches, probably because Tracker/Beagle took them all away.